Interactive-toy-concepts Storm Wolf Bedienungsanleitung PDF herunterladen

Web site: www.interactivetoy.com

PLEASE! DO NOT RETURN THIS

PRODUCT TO ANY RETAIL STORE!

PLEASE! DO NOT RETURN THIS

PRODUCT TO ANY RETAIL STORE!

For any questions or problems with this product please contact us at:

Email: info@interactivetoy.com

Phone: Inside North America: +1-416-444-6873

Outside North America: 1-866-214-2220

Address: Interactive Toy Concepts,

17 Vulcan Street, Toronto, Ontario, Canada. M9W 1L3

Manufactured by and distributed by Interactive Toy Concepts Ltd. Conforms to Safety Standards ASTM F963-03 Regulatory Requirements.

Products and colors may vary. MADE IN CHINA.

INS-55078-110614-US

Item# 44072

Limited 30-day warranty

Product is warranted by Interactive Toy Concepts Limited against

manufacturing defects in material and workmanship under normal use

for (30) days from the date of purchase.

Warranty is validated upon receipt of proof or purchase

and confirmation of UPC code.

Proof of Purchase

UNPACKING YOUR BLADERUNNER STORMWOLF HELICOPTER:

WARNING: The Storm-Wolf is a delicate machine, before removing it from the packaging please read the

instructions! To prevent damage during shipping, the Storm-Wolf is securely fastened in the package.

Please ensure that all of the tie-down and fastening locations are unfastened before attempting to remove

the Storm-Wolf Helicopter from the package. Be very careful when removing the Storm-Wolf to prevent

damaging the Helicopter.

COMPLETE PACKAGE CONTENTS AND COMPONENT BREAKDOWN:

Storm-Wolf Helicopter will

not start, LED on

Storm-Wolf Helicopter is

off.

1. Storm-Wolf Helicopter is not

turned on.

2. Battery is not charged.

3. Storm-Wolf Helicopter was not set

to off during charging.

4. Rotors locked for overload

protection.

1. Turn Storm-Wolf Helicopter on.

2. Charge Internal Storm-Wolf Helicopter Battery.

3. Ensure Storm-Wolf Helicopter is off and charge

Internal Storm-Wolf Helicopter Battery.

4. Slide Storm-Wolf Helicopter's On / Off Switch to Off,

then switch it On again.

Storm-Wolf Helicopter will

not start, LED on

Storm-Wolf Helicopter is

ON.

1. Storm-Wolf Helicopter's infrared

link is not established with the IR

Controller.

2. IR Controller is not turned on.

3. Storm-Wolf Helicopter’s battery is

low.

1. Push Left Stick (Throttle) completely UP, then back

DOWN to initialize infrared link and throttle control.

2. Turn on IR Controller.

3. Ensure Storm-Wolf Helicopter is off and charge

Internal Storm-Wolf Helicopter Battery.

CORRECTIVE ACTION:

CAUSE:

TROUBLESHOOTING

ISSUE:

Storm-Wolf Helicopter will

not start, LED on

Storm-Wolf Helicopter is

flashing.

1. Motor stall protection is activated.

2. Storm-Wolf Helicopter's Internal

Battery power is low.

1. Reset the Storm-Wolf Helicopter by turning its power

off and on.

2. Ensure the Storm-Wolf Helicopter is Off and

recharge the Internal Battery.

INSTRUCTION MANUAL

Balance bar

Tail Rotor

Tail Motor

Tail Boom

Landing Gear

LED Light

Charging Port

Top Rotor

Bottom Rotor

On / Off Switch

(other side)

Congratulations on the purchase of your BladeRunner

Storm-Wolf Helicopter. The Storm-Wolf brings advanced,

3-Channel, hobby-level flying technology to flyers who are

looking for great performance from an indoor Helicopter. The Storm-Wolf

has built-in advanced gyroscope technology for providing an ultra-smooth flight

and balance control assistance. In addition, the Storm-Wolf Helicopter has digital

proportional control. The Storm-Wolf is available in Infrared Control Channels A and

B. The compact and stylish design of the IR Controller has an integrated charging mechanism

so that only 6 AA Batteries in total are required to charge and operate the Storm-Wolf Helicopter.

Do not throw away this instruction manual as it contains valuable information for the operation of

your Storm-Wolf Helicopter as well as warranty information. The helpful tips in this Instruction

Manual will improve your skill and enhance your experience. Look for these symbols for

extra help.

1. BladeRunner Storm-Wolf Helicopter

2. IR Controller

3. Instruction Manual

4. 1 Replacement Tail Rotor

IR Control Emitter Window

Power Button

and Power LED

Trim Control Knob

Charge

LED

Charge Cable

Compartment Door

Left Stick

- Up / Down - Throttle

Right Stick

- Left / Right Steering

Direction Control

REPLACING DAMAGED ROTOR BLADES -Continued:

Main Rotor Blades:

1. Locate the broken Rotor Blade and use a fine Philips screw-driver (not included) to unscrew the tiny screw that

holds the Rotor Blade in place on the Hub Mount. Be careful not to lose the screw as it is tiny.

2. Pull the damaged Rotor Blade horizontally out and away from its location on the Hub Mount.

3. Install a new Rotor Blade in the same location on the Hub Mount by sliding it in horizontally. The holes for the

screw have to align. It is very important that the correct Rotor Blade is installed as the Upper and Lower Main

Rotor Blades may appear to be similar but are in fact very different. The Storm-Wolf Helicopter will not be able to

fly if the incorrect Rotor Blades are installed.

4. Fasten the new Rotor Blade to its Hub Mount with the same tiny screw that was pulled out earlier. Do not over

tighten the screw as the Rotor Blade needs to be able to spin freely inside its Hub Mount. Your Storm-Wolf

Helicopter is ready to fly again!

Tail Rotor:

1. Locate the broken Tail Rotor on the end of the Storm-Wolf Helicopter’s boom.

2. Remove the broken Tail Rotor by gently pulling it upwards off of the Tail Motor’s Axle Shaft.

3. Install the replacement Tail Rotor (Included with the Storm-Wolf) by sliding it onto the Tail Motor’s Axle Shaft in

the reverse process as outlined in step 2.

4. Gently press down on the replacement Tail Rotor until it is firmly in place.

REPLACING THE BALANCE-BAR-TO-UPPER-ROTOR CONNECTOR:

There is a small Connector which connects the Upper Rotor to the Balance Bar. In the event that this Connector

becomes disconnected, broken, or lost, it will need to be reconnected or replaced. A replacement Balance-Bar-

To-Upper-Rotor Connector is not included with the Storm-Wolf Helicopter. A replacement connector can be

purchased separately as part of the Storm-Wolf Replacement Parts Kit. Replacement is easy with the following

steps.

1. The Connector is attached by 2 simple ball joints. Remove the broken Connector by disconnecting it from the

Upper Rotor Hub Mount and the Balance Bar and pull it away. Once removed, the ball joints will be exposed. A

ball joint will be visible on both sides of the Upper Rotor Hub Mount, and a ball joint will be visible on both sides of

the Balance Bar. There will be a total of 4 ball joints visible!

2. Install the new connector following the reverse of step 1. The connector only needs to connect 2 of the 4 ball

joints. The Connector must connect a set of ball joints that are in vertical alignment only. Gently but firmly press

the Connector into position, connecting the Upper Rotor and the Balance Bar. The Connector will just snap into

the 2 ball joints as shown.

STORING THE STORM-WOLF HELICOPTER:

It is a good idea to store the Storm-Wolf Helicopter, IR Controller and this Instruction Manual together so no

components become misplaced or lost. Please respect the below points to extend the operational life of your

Storm-Wolf Helicopter during storage.

1. Product may be damaged or performance may be adversely affected if the Storm-Wolf Helicopter is not prop-

erly stored.

2. Never place any items on top of any components of the Storm-Wolf Helicopter.

3. Always keep your Storm-Wolf Helicopter in a cool dry place. Do not allow your Storm Wolf Helicopter to get

wet as it is not water resistant.

4. Keep the Storm-Wolf Helicopter away from pets and other household animals.

5. Do not rest your Storm-Wolf Helicopter on any potential heat source such as electronic equipment or a radiator.

Storm-Wolf Helicopter is

flying too high

1. You need to reduce the Throttle

Input.

1. Push the Left Stick (Throttle) gradually down.

Storm-Wolf Helicopter is

flying too low.

1. Needs more power (Throttle Input).

2. The battery in the Storm-Wolf

Helicopter is low.

1. Push the Left Stick (Throttle) gradually up.

2. Ensure the Storm-Wolf Helicopter is off and charge

the Internal Storm-Wolf Helicopter Battery.

Storm-Wolf Helicopter

doesn’t hover.

1. The Storm-Wolf Helicopter drifts

forwards/backwards.

1. Push the right stick up or down to compensate and

hold the Storm-Wolf Helicopter in position.

Helicopter doesn't fly

forward fast enough.

1. The Storm-Wolf Helicopter is not

designed for fast flight as it is an

indoor toy.

1) If desired, add a small amount of weight to the

bottom front area of the body by taping a paper clip or

something similar in weight and size onto it. However,

note that this will reduce the ability of the Storm-Wolf

Helicopter to fly backwards.

Storm-Wolf Helicopter

doesn’t fly backwards

1. The Storm-Wolf Helicopter only

flies backwards briefly then spins to fly

forward.

1. Aerodynamics make flying backwards more difficult

than flying forwards and this flight pattern is normal.

Practice flying backward and control the left / right

turning motion of the Storm-Wolf Helicopter to keep the

tail pointed in the direction you desire.

Storm-Wolf Helicopter is

flying too low.

1. Needs more power (Throttle Input).

2. The battery in the Storm-Wolf

Helicopter is low.

1. Push the Left Stick (Throttle) gradually up.

2. Ensure the Storm-Wolf Helicopter is off and charge

the Internal Storm-Wolf Helicopter Battery.

Storm-Wolf Helicopter

doesn't move forward fast

enough.

1. The Internal Battery charge is

getting low.

2. The Tail Rotor is damaged.

3. The Storm-Wolf Helicopter center

of gravity is no longer correct.

1. Turn the Storm-Wolf Helicopter off and charge the

Internal Storm-Wolf Helicopter Battery.

2. Replace the Tail Rotor with a new one included with

your Storm-Wolf Helicopter, or from the Storm-Wolf

Replacement Part Kit (available in stores)

3. Use light adhesive tape to mount a clip on the front

bottom of the Storm-Wolf Helicopter to add weight and

adjust the center of gravity. See also “Storm-Wolf

Helicopter doesn’t hover” issue.

Storm-Wolf Helicopter

always turns.

1. Trim Control is not set correctly.

2. The Main Rotor Blades have

sustained damage / or wear from use.

1. Adjust the Trim Control Knob on the IR Controller.

2. Replace the damaged Rotor Blades! It is danger-

ous to fly with damaged Rotor Blades! Replacement

Rotor Blades are not included, but can be purchased

separately as part of the Storm-Wolf Replacement Part

Kit.

The Main Rotor Blades

spin erratically causing

unpredictable flight

characteristics.

1. The Balance-Bar-to-Upper-Rotor

Connector is either broken or missing.

1. Install a new Connector using the instructions in the

“REPLACING THE BALANCE-BAR-TO-UPPER-

ROTOR CONNECTOR” section. Replacement Connec-

tors are not included, but can be purchased separately

as part of the Storm-Wolf Replacement Part Kit.

CORRECTIVE ACTION:

CAUSE:

TROUBLESHOOTING -Continued

ISSUE:

IMPORTANT SAFETY INFORMATION

Keep the Storm-Wolf Helicopter away from face, eyes and hair at all times. Keep fingers away from moving

rotors or propellers. Do not fly the Storm-Wolf Helicopter near or at other people or animals. Use caution when

flying, make sure people around you know that you are playing with the Storm-Wolf Helicopter. Recommended

for use indoors only in rooms without obstacles, breakable objects or fans. The IR Controller's built-in Charger

provided in this package is for charging the Storm-Wolf Helicopter ONLY. Do not use any other source to charge

the Storm-Wolf Helicopter. Do not attempt to overcharge your Storm-Wolf Helicopter. Follow the charging

instructions provided in this Instruction Manual. Do not attempt to replace the Internal Lithium Polymer Recharge-

able Battery inside the Storm-Wolf Helicopter! The Storm-Wolf Helicopter’s Lithium Polymer Rechargeable

Internal Battery is sealed inside the unit and is not replaceable. Any attempts to repalce the Storm-Wolf Helicop-

ter's Lithium Polymer Rechargeable Internal Battery will void the warranty.

1 2

INSTRUCTION MANUAL 1

Inhaltsverzeichnis

Seite 1 - INSTRUCTION MANUAL

Web site: www.interactivetoy.comPLEASE! DO NOT RETURN THISPRODUCT TO ANY RETAIL STORE!PLEASE! DO NOT RETURN THISPRODUCT TO ANY RETAIL STORE!For any qu

Seite 2

QUICK-START INSTRUCTIONS:1. The Storm-Wolf Helicopter needs to be charged once it is taken out of the box for the purposes of its first flight for op

Kommentare zu diesen Handbüchern

Keine Kommentare

Interactive-toy-concepts Storm Wolf Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Spielzeuge Interactive-toy-concepts Storm Wolf herunter. Interactive Toy Concepts Storm Wolf User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Spielzeuge Interactive-toy-concepts Storm Wolf